ADAPTIVE SWEEP CATIA V5 PDF

Mozuru Contextual commands are available on this field. So there are still two lines left in the sketch so that it can adjust with the guide curves. Written by Sahaj Panchal. For instance, with the apparently similar sketch only its construction differs, but there f5 a coincidence constraint between the sketch extremity and the point on the guiding cztia you can obtain the following results: Select the end point of the guiding curve to create another section.

Author:Mikagar Vomuro
Country:Norway
Language:English (Spanish)
Genre:Literature
Published (Last):21 December 2015
Pages:330
PDF File Size:1.23 Mb
ePub File Size:8.31 Mb
ISBN:229-5-61622-278-1
Downloads:26113
Price:Free* [*Free Regsitration Required]
Uploader:Kinris



Dolar A swept surface which maintains constraints assigned for the profile sketch with guide curve. Similarly, it is best to use angle constraints rather than tangency or perpendicularity constraints, to avoid changes in the sketch orientation as it is swept along the guiding curve. You are commenting using your Twitter account. So one can simply state that the profile shape have been modified ignoring the constraints applied! Figures below state the rest.

XY plane Guide curve 2 sketch…. Create a section here: Set the Deviation value: It is the surface on which the guiding curve lies, and is used to define the axis system in which the swept surface is created. At the location where the profile is drawn, a manipulator will appear, which you can drag along and visualize how the profile is being adjusted with guides while still maintaining constraints applied hover over it and drag.

The list in the Sections tab is automatically updated with: It lets you specify the relimitation type. You can choose to limit the swept surface only on the start section, only on the end section, on both, or on none. The smoothing is done for any discontinuity which angular deviation is smaller than 0. To find out more, including how to control cookies, see here: Once you exit the Sketcher by clickingyou return to the adaptive sweep command after the sketch selection, as described above in step 5.

The 3d cure is created with Combine tool, which is in fact a multi-cell element. In distinction, it can be stated that the adaptive swept surface retains the constrains — dimensional or geometric — created for the profile sketch with guide curves.

Upvote 0 Upvoted 1. In some cases, with tangency or perpendicularity constraints, the sketch may be inverted and lead to unsatisfactory results. If no guiding curve already exists, use the contextual menu in the Guiding Curve field to create, either a line, or a boundary. Click the Parameters tab to display and redefine the constraints on a given section.

Click preview daaptive see the surface and hit OK if the result is as required. Leave a Reply Cancel reply Enter your comment here Log in or sign up to answer. The surface is shown here. Creating Adaptive Swept Surfaces Impose more sections along the guiding curve Decrease the discretization step value to better define the sweeping along the guiding curve.

For instance, with the apparently similar sketch only its construction differs, but there is a coincidence constraint between the sketch extremity and the point on the guiding curve you can obtain the following results: The Parent field becomes current and is filled in with the parent to be replaced. Select a boundary on an adjacent surface as a constraining element when creating the sketch. These swept surfaces are created based on sections along the guiding curve and constraints that can be specified for each of these sections.

A new point is dropped on the guide curve with the corresponding ratio. In our example, araptive you wish to define a reference surface, select the xy plane. You also have the possibility to create your sketch using the Sketcher workbench before entering the Adaptive Sweep swedp, although it is advised to create it directly in the context of the Adaptive Sweep command.

Selecting a Reference Surface is optional. Ask and answer engineering questions Join the Community. Make sure that the profile catiaa intersecting with the guide curves, otherwise you have to define the intersection manually while creating the swept surface as anchor points. Sorry, your blog cannot share posts by email. Swewp for reading the post. Also the profile sketch requires to be under-constrained, meaning to say, you can assign as many constraints as you want in the profile, until there are enough entities left to adjust with the guide curves.

Downvote 0 Downvoted 1. You can select a Spine if you want it to be different from the guiding curve. Related Posts

ELITMUS QUESTION PAPERS PDF

please tell me about ADAPTIVE SWEEP IN CATIA V5 R16 with a suitable example

Dur Keep one thing in mind however, if the guide curve or the surface is a multi-cell element, you need to create a Join feature first and then use them, otherwise error would not be far away. Keep visiting for more. The Parent field becomes current and is filled in with the parent to be replaced. Fill in your details below or click an icon to log in: XY plane — can be any other plane adzptive well Make sure that the profile is intersecting with the guide curves, otherwise you have to define the intersection manually while creating the swept surface as anchor points.

ANGELA MCROBBIE THE AFTERMATH OF FEMINISM PDF

ADAPTIVE SWEEP CATIA V5 PDF

Click Here to join Eng-Tips and talk with other members! Already a Member? Read this white paper to learn more. In this white paper, learn how you can configure freely without requiring any custom development, and quickly update configurations as your needs evolve; retain product, customer and systems knowledge over time, even after employee turnover and generational changes; and future-proof your PLM with multiple updates a year, keeping you ahead of the pack with the latest platform capabilities. Our newest eBook gives a deep overview on how using 3D printed jigs and fixture aids work to streamline operations.

Related Articles